Garmin Marq 2: Troubleshooting “Inconclusive” ECG Readings

When taking an ECG reading on a Garmin MARQ Gen 2 luxury tool watch, receiving an “Inconclusive” result means the onboard sensor detected electrical activity, but the recorded waveform could not be safely classified by the diagnostic algorithm. The watch failed to produce a clean enough signal to confirm a normal Sinus Rhythm or identify signs of Atrial Fibrillation (AFib). This does not necessarily point to a medical emergency or a defective watch, it almost always indicates high electrical resistance, muscle micro-tremors, or an out-of-range heart rate during the 30-second recording window.

Quick Answer

Lightly moisten your wrist skin and the thumb and index finger touching the watch’s titanium bezel with a drop of water. Sit down, rest both forearms completely flat on a table to eliminate muscle tension, breathe normally, and confirm your resting heart rate is between 50 and 100 beats per minute before starting the test.


Device & Signal Snapshot

  • Device: Garmin MARQ Gen 2 Series (Athlete, Adventurer, Captain, Golfer, Aviator, Carbon)
  • Sensor Array: Garmin Elevate Gen 5 Optical & Electrical Sensor Hub
  • Hardware Interface: Rear sensor pad (wrist contact) and front titanium bezel/chassis ring (finger contact)
  • Result Code: Inconclusive (High Heart Rate, Low Heart Rate, Poor Recording, or Unclassified Rhythm)
  • Data Risk: Minimal (the ECG tracing is saved in Garmin Connect, but algorithmic classification cannot be completed)

What Is Actually Happening?

The Garmin ECG app records a single-lead electrocardiogram (equivalent to Lead I on a clinical 12-lead ECG). It measures the micro-voltage electrical impulses that make your heart muscle contract:

Lead I Electrical Pathway:
[Right Hand / Bezel Ring] ──> Arm ──> Torso / Heart ──> Left Arm ──> [Rear Sensor / Left Wrist]
                                            │
                          Micro-Tremors / Dry Skin Resistance
                                            ▼
                           Algorithm Rejects: "Inconclusive"

To complete this circuit, the back plate of the watch must maintain steady electrical contact with your left arm, while your right thumb and forefinger hold the exterior titanium ring (bezel) of the MARQ 2.

The MARQ 2’s algorithm rejects the signal and returns an “Inconclusive” result under three specific conditions:

  1. Poor Signal Integrity (Noise/Artifacts): The electrical noise generated by flexing arm muscles (electromyography noise) drowns out the tiny cardiac electrical signal (typically around 1 millivolt).
  2. Heart Rate Out of Range: The algorithm is clinically validated to classify rhythms only between 50 and 100 beats per minute (BPM). If your pulse is at 48 BPM or spikes to 105 BPM from test anxiety, the result is automatically flagged as inconclusive. For deeper insights on reading metrics, see What an “Inconclusive” ECG Result Actually Means for Your Health Data.
  3. Unclassified Cardiac Rhythms: Rhythms other than standard Sinus Rhythm or AFib (such as premature ventricular contractions, frequent extra beats, or bundle branch blocks) fall outside the algorithm’s diagnostic parameters.

How to Tell Which Problem You Have

The MARQ 2 app displays explanatory sub-text beneath the “Inconclusive” banner. Use that description to determine your next diagnostic step:

App Sub-TextRoot CauseImmediate Action
“Poor Recording”High skin resistance, low contact moisture, or movementHydrate skin contact points; stabilize arms flat on a hard surface
“Heart Rate Below 50 BPM”Bradycardia or athlete’s low resting heart rateStand up, walk lightly for 30 seconds to raise your heart rate above 50, then retest
“Heart Rate Above 100 BPM”Tachycardia, caffeine spike, or post-workout elevationSit calmly for 5 minutes, take slow breaths to drop your pulse below 100 BPM
“Rhythm Not Classified”Waveform was clean, but electrical signature deviates from standard AFib/Sinus patternsExport the PDF recording from Garmin Connect to share with a physician

Step-by-Step Recovery & Recording Protocol

Step 1: Lower Skin Contact Resistance (Impedance)

Dry, dead skin on the outer layer of your epidermis (the stratum corneum) is a poor electrical conductor. Titanium and stainless steel sensors need moisture to bridge the gap to your capillaries.

  1. Remove the watch. Lightly moisten the skin on your inner wrist using a drop of water, saline solution, or contact lens fluid.
  2. Lightly moisten the pads of your right thumb and index finger.
  3. Clean the back sapphire crystal and metal sensor ring of the MARQ 2 with a damp microfiber cloth to remove skin oil films.
  4. Put the watch back on, adjusting the strap so it sits securely roughly one finger-width above your wrist bone. It should be snug enough not to slide, but not tight enough to pinch.

Step 2: Eliminate Muscle Micro-Tremors

The tiny electrical pulses from your forearms holding your hands in the air will distort the recording.

  1. Sit comfortably in a chair at a desk or table.
  2. Rest both of your forearms completely flat on the tabletop.
  3. Rest your wrists and hands on the surface so that no arm muscles are supporting their own weight.
  4. Place your right thumb and index finger gently on the opposing sides of the outer metal bezel. Do not squeeze. Pressing down hard flexes the fingers, generating electrical interference (electromyographic artifact).
  5. Keep your hands and fingers relaxed throughout the 30-second countdown. Breathe slowly and evenly through your nose. Do not talk.
Electrode Touch Technique on MARQ 2:
┌───────────────────────────────────────┐
│              [ Bezel Ring ]           │
│         ▲                   ▲         │
│   Thumb Contacts       Index Finger   │
│   Left Bezel Edge   Right Bezel Edge  │
│                                       │
│   *GENTLE resting contact only*       │
│   *Do NOT press down or squeeze*      │
└───────────────────────────────────────┘

Step 3: Check Environmental and Electrical Interference

External electromagnetic fields (EMI) can corrupt sensitive biosensors:

  • Disconnect your phone or laptop from third-party or ungrounded wall chargers located within reach of your desk. Poorly shielded power adapters leak 50/60 Hz electrical hum directly through tabletop surfaces.
  • Step away from large appliances, high-draw fitness equipment (such as active treadmills), or heavy industrial equipment while recording.
  • If your skin is unusually cold, blood flow to your extremities drops, weakening the signal. Warm your hands and wrists before testing. For more on how temperature disrupts sensors, see How Cold Weather Causes “Flatlining” Heart Rate Readings (Skin Perfusion Issues).

What to Check If That Doesn’t Work

If every reading returns an inconclusive “Poor Recording” despite moist skin and steady hands:

  • Verify Watch Orientation Settings: In Garmin Connect, ensure your watch’s Wrist Placement setting (Left vs. Right wrist) matches the wrist you are actually wearing it on. If the watch expects to be on your left wrist but you wear it on your right, the electrical polarity is inverted, confounding the classification algorithm.
  • Firmware Integrity: Ensure the MARQ 2 has been updated via Garmin Express to the latest system software. Early software builds had stricter artifact rejection parameters that were refined in subsequent updates.
  • Review Diagnostic Raw Tracing: Open the Garmin Connect mobile app, go to Health Stats > ECG, tap the inconclusive recording, and choose Export a PDF for Your Doctor. Zoom in on the trace:
    • If the line is a continuous, spiky scribble, electrical interference or dry skin is breaking the baseline.
    • If the line shows clean, distinct, rhythmic cardiac spikes (P-waves, QRS complexes, T-waves) but the app still states “Inconclusive,” your heart rate was either out of range or your rhythm features variations that require a medical provider’s evaluation.

When It’s Actually a Hardware Problem

The MARQ 2 uses a physical, electrically isolated bezel that connects to the internal logic board via spring-loaded contacts.

If the watch has taken a hard hit, was subjected to salt water without being rinsed, or has accumulated built-up debris between the bezel seams and the watch case, the electrical path can degrade.

To test whether the metal bezel is registering touch at all, access the hidden diagnostic menu (see How to Access the Hidden Garmin Diagnostic Menu (Button Combinations)). If the test shows the bezel touch contacts reading open-circuit (0 or OPEN) when holding the ring, contact Garmin Support for service.


The Bottom Line

An “Inconclusive” result usually means muscle tension or dry skin interfered with the reading. Moisten your wrist and fingertips, sit at a table with both forearms resting completely flat, stay relaxed, and ensure your resting heart rate is between 50 and 100 BPM.