Smartwatch Low Power Modes are essential for long runs, weekend hikes, and long travel days. However, many users avoid using power-saving modes because they assume it disables heart rate tracking entirely, leaving workouts without calorie, strain, or cardiovascular data.
On modern smartwatches, you do not have to give up continuous heart rate tracking to save power. You can isolate energy-draining components—such as the Always-On Display, Wi-Fi radio, and background app refreshes—while keeping the optical heart rate sensor running continuously.
Quick Answer
To save battery without losing heart rate tracking, use specialized workout power settings rather than system-wide emergency battery savers. On Apple Watch, turn on Low Power Mode in Workout settings, but leave Fewer GPS and Heart Rate Readings turned Off. On Wear OS and Garmin, customize your Battery Saver profile to disable display and network radios while keeping the optical heart rate sensor set to On.
Device & Signal Snapshot
- Supported Hardware: Apple Watch (Series 4 through Ultra 2, watchOS 9–11), Samsung Galaxy Watch (One UI 5/6/8 Watch), Garmin (Fenix, Forerunner, Enduro series).
- Active Biometric: Optical Photoplethysmography (PPG) sensor array (green LED pulse monitoring).
- Disabled Subsystems: Always-On Display (AOD), cellular/LTE standby, Wi-Fi polling, background push notifications, and wrist-raise animations.
- Runtime Extension: Extends active workout tracking battery life by 50% to 100% without reducing cardiovascular data resolution.
What Is Actually Happening: System vs. Workout Power Saving
To preserve continuous heart rate monitoring, you need to understand the difference between the two types of power-saving modes:
[Standard Workout Tracking]
• Optical PPG: Active 1-second pulse sampling
• Always-On Display: Active 60Hz/1Hz rendering
• Background Radios: Wi-Fi, Cellular, BLE active
• Total System Draw: ~120 to 180 mW
┌────────────────────────┴────────────────────────┐
▼ ▼
[Generic Emergency Battery Saver] [Optimized Workout Low Power Mode]
Cuts optical sensors completely. KEEPS optical PPG tracking active (1-sec).
Disables screen and background OS. Turns off AOD (Screen on tap only).
Leaves watch as a basic digital clock. Cuts Wi-Fi and cellular connections.
No biometric tracking. Total System Draw: ~50 to 75 mW (Saves ~50%)
- System Emergency Battery Saver (Do Not Use): When your watch hits 5% or 10%, it prompts you to activate basic power saving. This mode drops the CPU to bare minimum clock speeds, turns off all optical sensors, and disables fitness tracking, leaving your watch as a simple digital clock.
- Targeted Workout Low Power Mode (Use This): This mode keeps your fitness tracking active while turning off the non-essential features that drain battery during workouts: display illumination, background app refreshes, and cellular connections.
Platform-by-Platform Setup
1. Apple Watch (watchOS)
Starting with watchOS 9, Apple introduced a flexible Low Power Mode that lets you choose whether to keep continuous heart rate monitoring.
[Settings > Workout] ──> [Low Power Mode: ON] ──> [Fewer GPS & Heart Rate Readings: KEEP OFF]
- Open Settings on your Apple Watch.
- Scroll down and tap Workout.
- Toggle Low Power Mode to On. (This automatically turns on Low Power Mode whenever you start an activity).
- Look directly below that toggle for Fewer GPS and Heart Rate Readings:
- KEEP THIS TOGGLED OFF: When kept off, your Apple Watch continues reading your heart rate every second, keeping your calorie, heart rate zone, and cardio data fully accurate. It saves power by turning off the Always-On Display, silencing incoming notifications, and shutting down background network requests.
- When to turn it on: Only toggle this setting on for ultra-endurance events (like 50-mile ultramarathons) where you need to stretch battery life up to 17 to 20 hours. When enabled, it drops GPS fixes to periodic pings and takes heart rate readings only once per minute, which reduces workout data accuracy.
To adjust your regular day-to-day display power without compromising workout metrics, review The “Always-On Display” Audit: How Much Battery Are You Actually Saving?.
2. Samsung Galaxy Watch (Wear OS)
Samsung splits power saving between system limits and fitness tracking settings:
- Configure Workout Display Limits:
- Open Samsung Health on your watch.
- Tap Settings > Heart Rate.
- Ensure it is set to Measure continuously (not Every 10 minutes).
- Apply Power Saving During Activities:
- When starting a run or walk, open the workout target screen and enable Audio Guide off and Screen off during exercise.
- Turn on Power Saving in your quick settings shade. In modern Wear OS versions, this caps CPU usage at 70% and disables the Always-On Display, but continues recording your active heart rate throughout your workout.
If you notice rapid heart rate spikes while running in power-saving modes, read PPG Sensor “Shadowing”: Troubleshooting Inaccurate Spikes During High-Intensity Intervals.
3. Garmin Watches (Fenix, Enduro, Forerunner)
Garmin allows you to customize every aspect of your battery profiles using Power Manager:
- On your watch, hold the Up/Menu button and select Power Manager.
- Tap Power Modes and select Add New (or edit Max Battery).
- Configure the parameters individually:
- Wrist Heart Rate: Set to Turn On (or Don’t Change).
- GPS: Set to GPS Only or UltraTrac (depending on your required route precision).
- Display / Backlight: Set to Off / Timeout.
- Phone Connection: Set to Disconnect.
- Music: Set to Disable.
- Save this profile as “Endurance Workout.” Assign it to your running or hiking activity profiles so your watch automatically tracks biometrics while shutting down all other power-draining features.
The Ultimate Battery Hack: External Bluetooth Chest Straps
If you want the absolute longest battery life from your watch without sacrificing heart rate accuracy, pair your watch with an external Bluetooth heart rate chest strap (like a Polar H10 or Garmin HRM-Pro).
[Internal Watch Optical Sensor] ──> High-power LEDs pulse continuously (~30-50 mW)
│
(Pair External Strap)
│
▼
[External Bluetooth Strap] ──> Internal watch LEDs shut off completely.
Watch simply receives a tiny BLE data packet.
Net power draw drops by up to 35%.
When you pair an external strap, your watch’s internal optical LEDs turn off completely. The watch simply receives a low-power Bluetooth data packet once per second, extending your watch’s workout battery life by up to 20% to 35% while providing ECG-grade heart rate data.
To learn how steady workouts impact energy use, see Understanding “Steady State” HR: Why Your Watch Fails During Intervals.
Bottom Line
You do not have to give up heart rate tracking to save battery. Use your watch’s Workout Low Power Mode while keeping reduced-sampling options disabled, or connect an external Bluetooth heart rate strap to shut down the watch’s internal sensor LEDs entirely.