How to Clear the “Data Not Cleared, Sync & Try Again” Fitbit Loop

The “Data not cleared. Sync & try again” error appears when a factory reset fails midway through wiping your Fitbit. This error occurs because the device’s security architecture will not clear encrypted user partitions—especially security tokens for contactless payments and stored biometrics—without an authenticated server handshake. When that handshake drops during the wipe, the tracker locks itself in a boot loop to prevent unauthorized data exposure.

Quick Answer

Break the loop by unpairing the Fitbit from your phone’s Bluetooth settings and removing it from the Fitbit app. Next, attach the tracker to its official charging cable and perform a manual hardware reset using the physical button sequence on the cable or watch chassis. This forces a raw flash memory wipe without requiring a Bluetooth connection.


Device & Signal Snapshot

  • Affected Devices: Fitbit Charge series (Charge 4, 5, 6), Versa series (Versa 2, 3, 4), Sense series (Sense, Sense 2), and Luxe
  • Visual Symptoms: Red circle with an “X” or exclamation icon, accompanied by the scrolling message “Data not cleared. Sync & try again”
  • System State: Microcontroller is locked in bootloader recovery; the standard user interface and sensor tracking are completely inaccessible
  • Risk Factor: Existing on-device data is already flagged for deletion and cannot be recovered

What Is Actually Happening?

When you trigger a factory reset on a modern Fitbit, the operating system executes a three-phase cryptographic scrub:

[Phase 1: Token Revocation]
     │   Tracker contacts Fitbit/Google servers via Bluetooth to revoke
     │   Google Wallet / Fitbit Pay tokens and account authentication.
     ▼
[Phase 2: Partition Demolition]
     │   Internal storage partitions (user data, biometric logs, cached GPS)
     │   are unmounted and overwritten.
     ▼
[Phase 3: Bootloader Reset]
         Hardware restarts into out-of-box setup state with clean firmware.

The loop occurs when Phase 1 fails after Phase 2 has already started. If the Bluetooth connection drops or the phone app terminates while tokens are being revoked, the system detects an incomplete security clear. To protect your payment information, the bootloader refuses to boot normally and refuses to complete the wipe without confirming the remote sync.

Because the tracker is half-wiped, it can no longer communicate properly with the companion app, creating an endless cycle.


How to Break the Loop

To fix this issue, you must bypass the Bluetooth handshake and force the hardware controller to complete a cold storage erase.

Step 1: Sever All Stale Phone Connections

Do not try to sync the phone until the device is scrubbed. Old Bluetooth bonds will interrupt the recovery attempt:

  1. On your phone, go to Settings > Bluetooth.
  2. Locate your Fitbit device in the paired devices list, tap the info icon or gear, and select Unpair or Forget This Device.
  3. Open the Fitbit app, tap your Profile icon > Devices, select your tracker, and tap the Trash icon (Remove this device).
  4. Turn off your phone’s Bluetooth completely to prevent it from attempting a background handshake.

Step 2: Perform the Model-Specific Hardware Force-Wipe

For Fitbit Charge 5, Charge 6, and Luxe (Charger Button Method)

These models lack mechanical chassis buttons and rely on the wired charging cable to send a reset pulse to the power management integrated circuit (PMIC):

  1. Plug the official charging cable into a powered USB wall adapter (avoid low-power computer ports).
  2. Seat the tracker securely into the magnetic charging cradle. Ensure the pins make solid contact.
  3. Locate the small button on the flat side of the USB plug.
  4. Press the button 3 times within 8 seconds, holding each press for roughly 1 second and pausing for 1 second between presses.
  5. Watch the display carefully. Within 10 seconds of the third press, the device will briefly show a battery icon, blink, and display the Fitbit logo.
  6. When the logo appears, the raw flash memory has cleared, and the screen should display a setup prompt (a smartphone icon or URL).

For Fitbit Versa 3, Versa 4, Sense, and Sense 2 (Chassis Force-Wipe)

  1. Remove the watch from the charger.
  2. Press and hold the solid-state side button for 8 to 10 seconds until the screen turns completely dark.
  3. Keep holding the button. When the Fitbit logo flashes on screen, release the button for 1 second, then immediately press and hold it again.
  4. Hold the button until you feel a distinct vibration. This vibration indicates the watch has entered raw recovery mode.
  5. Release the button. The watch will wipe its internal storage and reboot to the initial pairing screen.

If your device continues to display persistent system crash errors or an Error 1001 alert after these procedures, refer to Fitbit Error 1001: Fixing the “Data Not Cleared” Factory Reset Loop.


What to Check If That Doesn’t Work

If the “Data Not Cleared” screen immediately returns after a hardware reset attempt, one of two conditions is blocking the recovery:

  1. Dirty or Pitted Charging Pins: On the Charge and Luxe series, the reset pulse travels directly through the charging pins. If micro-corrosion or dirt coats the gold contacts, the signal will not reach the logic board. Clean the pins according to How to Clean Wearable Charging Pins: The Eraser vs. Alcohol Method.
  2. Bootloader Freeze: If the screen locks onto the initial startup icon without progressing to the setup prompt, review Why Your Fitbit Charge 6/Sense 2 is Stuck on the “Smile” Logo to unfreeze the base firmware.

Bottom Line

The “Data Not Cleared” loop is a security failsafe triggered by an interrupted wipe; eliminate phone Bluetooth interference and use the charging cable or hardware button reset to force a low-level flash wipe.