Watching your Oura Ring Gen 4 firmware update crawl all the way to 99% only to throw a “Something went wrong” error usually means the file finished transferring, but your phone lost its Bluetooth handshake right when the ring rebooted to install it. In many cases, the update either installed anyway or tripped over background phone power limits, a sleeping USB charger, or a stale Bluetooth bond.
Quick Answer
An Oura Ring Gen 4 update that fails at 99% usually drops during the final post-reboot Bluetooth reconnect. First, check your ring’s Firmware Version in the Oura App—it may already be updated. If not, seat the ring firmly on a wall-powered charger, keep the app open in the foreground, and toggle Bluetooth before retrying.
What Is Actually Happening?
An Oura Ring firmware update happens in two separate stages over Bluetooth Low Energy (BLE):
- Transfer stage (0% to ~98%): Your phone downloads the firmware package over Wi-Fi or cellular data and pushes it piece by piece to your ring’s internal memory.
- Verify and reboot stage (99% to 100%): The ring verifies the package, shuts down briefly to flash the new firmware, and reboots so the Oura App can reconnect and confirm the new version number.
That 99% mark is where things break most often. If your phone locks its screen and pauses background Bluetooth, if your ring loses steady power on the dock, or if your phone clings to the ring’s pre-reboot Bluetooth state, the final confirmation fails and triggers the generic “Something went wrong” prompt.
First Check: Did the Update Actually Succeed?
Before starting over, verify whether the flash completed silently before the Bluetooth handshake timed out:
- Force-close the Oura App and reopen it.
- Tap the menu icon in the upper-left corner and select My Oura Ring.
- Check the listed Firmware version against the latest version prompted in the app.
If the update prompt disappears and your firmware version moved up, you are already finished—no further troubleshooting needed.
What Causes the 99% Failure
- Phone screen lock or battery saver mode: Both iOS and Android aggressively throttle Bluetooth transfers when an app leaves the screen or when Low Power / Battery Saver mode is active.
- Underpowered or sleeping USB port: Plugging the Gen 4 charging dock into a laptop port that goes to sleep, an unpowered hub, or a finicky fast-charge brick can interrupt power right as the ring reboots.
- VPN or unstable internet: The Oura App checks in with Oura’s servers at the start and end of an update; active VPNs or weak public Wi-Fi can break that final verification.
- Stale Bluetooth pairing cache: After the ring reboots with new firmware, your phone sometimes refuses to complete the final reconnect until you clear the old BLE bond.
What to Do: Step-by-Step Fix
Step 1: Stabilize Power, Network, and Screen Focus
- Plug your Gen 4 charger cable directly into a standard wall adapter—avoid computer USB ports or multi-port hubs.
- Wipe the inside of the ring and the charger surface gently, then seat the ring flat on the dock until the charger LED confirms charging. (For light behavior details, check How to Fix Oura Ring “Firmware Update Timed Out” (The Charger Placement Hack).)
- Turn off any VPN and Battery Saver / Low Power mode on your phone, and switch to a steady home Wi-Fi connection.
- Keep your phone right next to the charger, open the Oura App, and keep the screen awake (tap the screen occasionally so it does not lock) until the update finishes.
Step 2: Refresh the Bluetooth Handshake
If the update stops at 99% again:
- Force-close the Oura App completely.
- Open your phone’s Settings > Bluetooth, turn Bluetooth off for at least 10 seconds, then turn it back on.
- Reopen the Oura App, allow any pending data sync to finish first, and retry the update.
Step 3: Reset the Bluetooth Bond
If repeated retries fail right at 99%, your phone’s Bluetooth cache is likely holding onto a stale connection profile:
- Back up your data by letting the Oura App sync normally if possible.
- Go to your phone’s Bluetooth settings, find your Oura Ring in the paired devices list, and choose Forget This Device (or Unpair).
- Restart your phone completely.
- Follow How to Force a Bluetooth “Bonding” Reset for Oura and WHOOP to re-establish a clean connection, then run the firmware update again.
What to Check If That Doesn’t Work
If the update still fails after resetting the Bluetooth bond—or if your ring stops appearing in the app altogether—you may need to reset the ring’s controller before trying again:
- Perform a Soft Reset: If the app is still connected, use the Soft Reset option under My Oura Ring in the Oura App, or follow The Oura Ring “Soft Reset” Protocol (The 6-Tap Charger Trick). A soft reset refreshes the ring’s hardware state without wiping your synced history.
- Watch for post-update connection loss: If the ring disappears from Bluetooth after a failed flash, see “Ring Not Found” After Update: Forcing an Oura Factory Reset Without the App. Note that a factory reset erases any unsynced data stored locally on the ring, so only use it if syncing and soft resets fail.
When It’s Actually a Hardware Problem
Stop repeating firmware attempts and contact Oura Support if you observe any of these hardware signs:
- The charging dock shows a solid red LED or refuses to light up across multiple known-good wall outlets and USB-C cables. Check Oura Ring Solid Red LED: Is Your Hardware Bricked? to confirm what that signal means.
- The ring charges to full, yet disconnects within seconds of lifting off the charger or gets noticeably hot on the dock.
- The ring fails to appear in Bluetooth scans on two different phones after a soft reset.
Repeatedly forcing flashes on a failing battery or damaged dock will not fix a hardware fault and falls under warranty or replacement support.
Bottom Line
When an Oura Ring Gen 4 update stalls at 99%, verify your Firmware Version first—it often already finished. If it genuinely failed, put the dock on a wall outlet, keep your phone screen awake in the Oura App with VPNs off, and reset the Bluetooth bond if the handshake stays stuck.