Placing your wearable on its charging dock only to see a “Sync Not Available” message in your companion app is frustrating when you want to review the day’s stats. This warning occurs because wearable firmware deliberately locks out certain wireless transmission channels while charging. The limitation protects hardware from thermal runaway, prevents radio-frequency interference from charging coils, or avoids data conflicts when a USB port switches the watch into mass storage mode.
Quick Answer
“Sync Not Available” during charging is an intentional thermal and operating system safeguard. Wearables disable Bluetooth Low Energy (BLE) sync while charging to prevent processor heat build-up or because the charging port has locked the storage drive. To clear it, allow the device to finish charging, cool down, or lift it briefly to sync off-dock.
Device & Signal Snapshot
- Affected Devices: Garmin, Fitbit, Wear OS (Pixel Watch, Galaxy Watch), Apple Watch, and smart rings (Oura)
- Affected Function: Companion app synchronization, cloud data push, local BLE data bus
- Severity: Low (No data is lost; transfer is merely queued until charging terminates or temperatures drop)
What Is Actually Happening?
When a wearable sits on an active charger, three internal constraints can suppress wireless synchronization:
- Thermal Throttling (BMS Lock): Lithium-ion batteries generate heat while accepting current, especially with magnetic fast chargers. High-speed processor operations, such as crunching cryptographic keys or running full-speed Wi-Fi/BLE radios, generate additional heat. The Battery Management System (BMS) signals the operating system to shut down non-critical background services to keep the device within safe charging temperatures.
- USB Mass Storage Priority: If your device is connected via USB to a computer, laptop, or smart vehicle port, the operating system mounts its storage partition over the physical wire. The device cannot simultaneously read/write files over BLE while a host operating system has an exclusive file lock on the storage controller.
- Electromagnetic Interference (Inductive Noise): Wireless charging pucks use high-frequency electromagnetic induction coils. On compact boards, this field creates radio-frequency noise that degrades weak Bluetooth signals, causing high packet drop rates. Firmware simply reports “Sync Not Available” rather than failing repeatedly.
How to Clear the Error
"Sync Not Available" Error
│
Is device connected to PC or Wall Adapter?
│ │
PC / USB Wall Adapter
│ │
Switch to wall plug ▼
│ Is watch hot to touch?
│ │ │
│ Yes No
│ │ │
│ Let cool for Check BLE & App
│ 10 mins Permissions
│ │ │
└─────────────┴───────┬───────┘
│
▼
Remove device from dock;
verify instant BLE handshake
Step 1: Change Your Power Source
If your wearable is plugged into a laptop, gaming console, or USB hub, the watch may think it is connected to a computer rather than a wall outlet.
- Disconnect the cable and plug it into a standard 5V/1A wall adapter.
- Avoid high-wattage charging blocks that force rapid power delivery handshakes unless your device explicitly supports fast charging.
- For Garmin-specific data-pin issues, see Garmin USB-C vs. Proprietary Pins: Troubleshooting “Cable Not Recognized”.
Step 2: Let the Battery Cool Down
If you docked your wearable immediately following an intensive workout, its internal temperature was already elevated. Adding charging current forces thermal protection to trigger.
- Leave the device on the charger for 15 minutes untouched.
- If charging paused entirely due to heat, review “Charging Paused”: Fixing Overheating Issues During Apple Watch Fast Charging.
- Once the battery cell temperature returns to standard operating range, the firmware will quietly release the BLE lockout.
Step 3: Perform the “Lift and Handshake” Test
To verify whether the issue is a software hang or an active hardware lock:
- Lift the wearable 2 inches off the charging puck or cradle.
- Open your companion app and swipe down to refresh.
- If the sync succeeds immediately, the lock is hardware-driven (thermal or electromagnetic) and completely normal.
- Place the wearable back on the dock once the sync completes.
What to Check If That Doesn’t Work
If the error persists even after taking the device off the charger:
- Stuck BLE Service Stack: The smartphone’s Bluetooth stack may still consider the device in a suspended state. Toggle your phone’s Bluetooth off for 10 seconds, then back on. For deeper steps on resetting the low-energy connection, see Why Your Wearable is “Connected” but Not Syncing: The BLE Service Reset.
- App Optimization Aggression: Android and iOS occasionally kill the background sync service while a phone is stationary. Open your phone’s Battery Optimization settings and ensure your companion app is set to Unrestricted.
Closing
“Sync Not Available” while docked is almost always a protective safeguard designed to prevent battery overheating and radio interference; simply allow your device to complete its charge cycle or pull it off the dock for 30 seconds to force an immediate sync.